![]() ![]() default functions are as follows: Arming this button to arm your system in the Stay mode. Pressing and holding a key will continuously transmit that function. If you are in Functions 5-8 or 9-12 the unit will ‘time out’ after 5 seconds if no but- are pressed. The WS4959 always defaults to functions 1-4 so it is not necessary to hold the center button to functions 1-4. Press one of the four buttons and the will stop flashing. The LED will pulsate that to indicate that you are in the appropriate functions. When you see the appropriate color LED, release the center button. The RED LED indicates functions 1-4, the GREEN LED indicates functions and the AMBER LED indicates functions 9-12. Watch as the LED on the WS4959 changes from red to green to 1 3 2 4 and back to red. ![]() Press and hold the center button of the WS4959. of the WS4959 small center button on the WS4959 is used as a level shift to from functions 1-4, 5-8 and 9-12. This is the remote to add to DSC’s new garage relay module with inte- laser parking (RXL2-433) to control anything that can be ON or OFF. This will allow you to arm and disarm, control garage doors and secu- gates, as well as a variety of other remote functions. Digital Security Controls, Toronto, Canada Support: 1-80 (cid:127) in Taiwan 9 0 0 7 0 5 1 R0 0 2 12-Function Wireless Key Instructions WS4959 is the industry’s first 12-function remote control. 160A-WS4959 The term before the radio certification number only signifies that Industry Canada technical specifications were met. Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. device complies with Part 15 of the FCC Rules. 32o to 120oF (0-49oC) 5-93% RH Water Resistant COMPLIANCE STATEMENT Changes or modifications not expressly approved by Digital Security Controls could void your authority to use this equipment. If batteries are swal- promptly see a doctor. Dis- of used batteries must be made in accordance with the waste recovery and recycling regulations in your Do not try to recharge these batteries. REPLACE WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER. DANGER OF EXPLOSION IF BATTERIES ARE INSTALLED INCORRECTLY. Improper handling lithium batteries may result in heat generation, explosion or fire, which may lead to personal injuries. ![]() The polarity of the battery must be observed, as shown in the diagram above. If the battery is low the trouble light on the controls panel’s will turn ON. During button press the key will send the status of its battery to the control receiver. normal conditions the batteries can last from 5 to 8 years. Replace both batteries with CR-2025 lithium batteries (see diagram). Remove the screw at the of the board to expose the batteries. Wireless Keys #9-16 Partition Assignment = OFF Option 1 ON #9 Partition2 OFF Option 8 #16 Partition2 Partition1 3 – Program Function Buttons, subsections –, subsections – (RF5501-433 v5.0)* Partition 1 Wireless Key Options * Partition 1 Wireless Key Options (RF5501-433) 3 Button 1 Stay Arming 4 Button 2 Away Arming 7 Button 3 Disarm 0 Button 4 Panic 3 Button 1 Stay Arming 4 Button 2 Away Arming 7 Button 3 Disarm 0 Button 4 Panic 3 Button 1 Stay Arming 3 Button 1 Stay Arming 4 Button 2 Away Arming 4 Button 2 Away Arming 7 Button 3 Disarm 7 Button 3 Disarm 0 Button 4 Panic 0 Button 4 Panic other options please refer to your appropriate receiver manual Partition 2 Wireless Key Options * Partition 8 Wireless Key Options (RF5501-433) the Batteries replace the battery, remove the top cover by inserting a coin into the slot on the bottom right corner and twist. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |